Category:304 Aggregate Base Course - Engineering Policy Guide

Where required, measurement of aggregate base course, complete in place, will be made to the nearest square yard. Where the aggregate base course extends to the inslope of the shoulder, the pay limit of the aggregate base course will be measured from the mid-point of the sloped portion.

Typical Road Structure Cross Section - Sub Grade, Base ...

In coarse grain, aggregate retained by #10 sieve, %age of wear shall not be greater than 5%. The max dia of any particle shall not be greater than 2/3ed of the layer thickness of sub-base. Typical particle size distribution for the sub-base (granular) when will meet strength requirement are:

Aggregate Base Density Data - Earthwork/grading ...

Jun 09, 2005· I am converting (CY) of aggregate (for a road construction project) to (TONS). Does any one have scientific data to use for the density of aggregate base rock? Several sources state that "most natural" aggregates have particle densities between 150 and 181 (lb/ft^3).


P-208 SPECIFICATION P–208. AGGREGATE BASE COURSE DESCRIPTION 208–1.1 This Work consists of a base course composed of hard, durable particles or fragments of crushed coarse aggregate blended with either binder and fine aggregate or filler. Construct it on a prepared underlying course in accordance with these Specifications and in conformance


Crushed Aggregate Base Coarse (Compaction Gravel) shall consist of one or more courses or layers of coarse aggregate, either crushed gravel or crushed stone, fine aggregate and binder or filler blended as necessary to produce an intimate mixture of the required gradation and stability.

Base Aggregate Calculator -

This script helps estimate the aggregate tonnage required for a particular job. To use this calculator, enter the appropriate width, length, and thickness of this application. Click on the measuring designator for thickness in feet or inches. Then, click on either Base Rock, Drain Rock, or a …

Bases and Subbases for Concrete Pavement

Bases and Subbases for Concrete Pavements (AASHTO) classification A-6 or A-7 soil groups or the Unified Soil Classification System CH, MH, and OH soils. o Degree of moisture change within the soil. Other factors responsible for non -uniform foundation include variability due to a number of reasons including, natural causes, excavation and


SECTION 02621 AGGREGATE BASE AND SUBBASE COURSES 02621.01 GENERAL A. Description Aggregate base and subbase courses shall include, but not necessarily be limited to, furnishing and placing one or more courses of aggregate, including additives when required, on a surface prepared in accordance with the Contract Documents. B. Related Work ...


The most recent Aggregate Base Course (ABC) unit weight test results performed by the NCDOT M&T Soils lab can be queried using this page. Use the drop down boxes to select the company and/or quarry submitting the sample. To see the results of all tests, click on the "Search" button without specifying a company or quarry.


Crushed Aggregate Base Coarse (Compaction Gravel) shall consist of one or more courses or layers of coarse aggregate, either crushed gravel or crushed stone, fine aggregate and binder or filler blended as necessary to produce an intimate mixture of the required gradation and stability.

02204 - Base Course - Juneau

A. Aggregate base course shall consist of crushed gravel or crushed stone, conforming to the quality requirements of AASHTO M 147. The aggregate shall be free from lumps, balls of clay, or other objectionable matter, and shall be durable and sound. B. Base course material shall conform to one of the following gradations as specified:

32 11 23 Aggregate Base Course - UDFCD

SECTION 32 11 23 AGGREGATE BASE COURSE . PART 1 GENERAL . 1.01 SECTION INCLUDES . A. The WORK to be performed includes the preparation of the aggregate base course foundation; and the production, stockpiling, hauling, placing, and compacting of aggregate base course…

Aggregate Base Courses - Buildipedia

Aug 14, 2009· An aggregate base course is the layer of soil installed between the surface pavement layer and subgrade (foundation soils) of either flexible or rigid pavement.Their purpose is to help transition surface loads from the pavement to the subgrade, evenly support the pavement surface profile, and protect the overall pavement system from water intrusion and deformation.

Section 815 Graded Aggregate

Section 815—Graded Aggregate 815.1 General Description This section includes the requirements for material to be used for base, subbase, or shoulder course material, and includes graded aggregate, unconsolidated limerock base, and crushed concrete base. 815.1.01 Related References A. Standard Specifications Section 800—Coarse Aggregate

Base Course - Halquist Stone

There are two categories of based course. Dense graded Bases, referred to locally as traffic bond, are well graded and include fines that firm up and become a hard, solid base for a variety of uses in construction. In general, the heavier the load, the larger the stone you will select in your base course.

Asphalt Concrete Base (ACB) - Pavement Interactive

Asphalt concrete base (ACB), also called asphalt treated base (ATB), is a dense-graded HMA with a larger nominal maximum aggregate size (1 inch) intended for use as a base course or binder course (see Figure 1). In addition to site paving benefits, ACB can be advantageous because it can provide: A waterproof barrier to prevent fines infiltration into the subgrade and pavement structure.

Graniterock: Technical Reports

Aggregate Baserock Primer. Aggregate Baserock is a dense graded blend of coarse and fine aggregate which when properly placed and compacted provide a stable and durable base allowing further construction. Aggregate Baserock Should Demonstrate: Stability: Resist deformation when under load (after proper placement and compaction).


1. Section 302 – Salvaged Base Course, Aggregate Base Course, or Aggregate Surface Course. 2. Section 816 – Aggregates 1.04 Submittals A. Submit gradation sample report for aggregate being used. 1.05 Sequence and Scheduling A. Prior to installing aggregate base, the subgrade must be test rolled for conformance to Specifications. The test ...

Construction Aggregate Calculator - Vulcan Materials Company

Construction Aggregate Calculator Enter the width, length, thickness, and product density and hit the "Calculate" button to calculate your estimate. If you do not know the product density, use the optional density estimator* or contact a local sales representative.

Airport Construction Standards (AC 150/5370-10) – Airports

Provides individual specifications from AC 150/5370-10, Standards for Specifying Construction of Airports, including construction standards for general provisions, earthwork, flexible base courses, rigid base courses, flexible surface courses, rigid pavement, fencing, drainage, turfing, lighting installation, pavement rejuvenation


As illustrated at the right it's simply a matter of taking the height at the tallest point and the width at the base of the triangle and then multiplying those by half. So in this case the formula you need is: Area = 0.5 x Width x Height. Height In Feet Width In Feet Total Square Feet.

Aggregate Base Course | Acme Sand & Gravel

The base course or basecourse in pavements is a layer of material in an asphalt roadway, race track, riding arena, or sporting field.It is located under the surface layer consisting of the wearing course and sometimes an extra binder course.. If there is a sub-base course, the base course is constructed directly above this layer.

P-208 Aggregate Base Course -

P-208, Aggregate Base Course Page 3 of 5 The base material shall be stockpiled, either at the plant or on the worksite, prior to placing and spreading on the prepared underlying course. (b) Materials of Proper Gradation. When the entire base course material from coarse to fine is secured in a uniform and well-graded condition and contains